Car Audio Power Wiring and Power Accessories

There may be no more boring subject then car audio wiring. There isn't too much to get excited about because wiring at its best should add absolutely nothing to the sound of the system. It should simply pass electrons from point A to point B. However it is a very important part of a car audio system and needs to be taken seriously.

Car Audio Power Wire

Power wire is one of the most important parts of an amplifier installation. The proper gauge is the second most important consideration, next to fusing. The proper gauge should be used so that the amplifier is not choked by the size limitations of the wire. When selecting a power wire, be sure to purchase one that has many hundreds or thousands of strands so that it will be easier to install and will not break when passing around sharp corners. Look for wires made from oxygen free copper (OFC). Also make sure that the jacket of the wire is of a material that will resist chemicals such as oil and battery acid that it will encounter in the engine compartment. To determine the size of the power cable you will need you can use the IASCA recommended wire size chart.

You can usually figure out the current draw of your system by adding up the fuse sizes of all of your components. For example, if you have two amplifiers that have fuses of 40 amps and 30 amps then you'll need a power wire capable of carrying 70 amps. Then determine the distance from your battery to your amplifier mounting location. Make sure you account for any bends and turns in the wire. This is not an exact science but try to get it close. If this distance is 15 feet then you look at the chart and find where the 70 amp row and the 15 foot column intersect. In this example we get 2 gauge wire. The IASCA wire chart tends to run a bit on the generous side. You might also consider using the online calculator provided at StreetWires.

In-line Fuse Holder Image courtesy of Parts Express

A word about fuses. Install an in-line fuse holder (see photo) for the power wire as close as possible to the battery terminal connection (the IASCA and USACi rule is within 18"). VERY, VERY IMPORTANT!!!!! This fuse protects your vehicle from burning up in case the power wiring shorts out. The wire between the fuse and the battery terminal will be unprotected, which is why you want this section to be as short as possible. The fuse size depends on the current the power wire will carry. Consult the owner's manual of your amplifier(s) to find out the maximum current draw of your system. You can also contact the manufacturer and ask them for that information. For multiple amplifiers you will need to add up the maximum current draw of each amplifier. Once you know the maximum current draw you'll know what size fuse to use. For example, if your maximum current draw is 50 amps then you'll need a 50 amp fuse. Do not insert the fuse until all other connections are made.

Car Audio Speaker Wire

Speaker Wire Image courtesy of Parts Express

Speaker wire is also important in terms of size and strands for the same reasons but the jacket is not as important because it will not see the same chemicals as the power wire. When shopping for speaker wire, look for oxygen free copper (OFC) wiring. The size of your speaker wiring depends on the amount of power going to your speakers and the length of wire from the amplifier to the speakers. Most systems will need to use 16 gauge to 12 gauge wire. Rarely would you want anything larger or smaller than that.

Car Audio Signal Cables

Signal or RCA cables are important for their noise rejection properties. Cables range in price from a couple of dollars to over one hundred dollars a pair. Most cables in the twenty to thirty dollar range (for a twenty foot pair) should be adequate for most listeners and noise situations. Twisted pair cables offer better noise rejection as opposed to coaxial cables (the most common). Twisted pair cables consist of two small gauge wires that are twisted around each other in a helix pattern. Coaxial cables are one small gauge wire jacketed by a braided cable which is then encased in a plastic jacket. The advantage of the twisted pair cables is in the twist. By twisting the cables noise picked up by one cable will be canceled by that same noise in the opposite cable (at least that's the theory). Twisted pair cables can be difficult to find so ask for them specifically when buying RCA cables.

Coaxial Type RCA Signal Cables Image courtesy of Phoenix Gold	Twisted Pair RCA Signal Cables Image courtesy of Rockford Fosgate

Car Audio Power Capacitors

In-line Fuse Holder Image courtesy of Stinger

Power capacitors or Stiffening™ capacitors are used to assist an automobile that has a problem with dimming lights (voltage sag) and to help "tighten up" the bass. These capacitors store a large amount of power and then release it very quickly when the demand is the greatest from the amplifier. These capacitors release the current much faster than a battery can and do not force the amplifier's power supply to be at a loss when bass notes and other transients are greatest. Capacitors should be chosen in the ratio of one Farad per thousand watts. Click here to read the chapter on power capacitors.

Car Audio Batteries

If extended engine off listening is desired then a second battery can be useful. Keep in mind that this will put a greater strain on your charging system as well as add several hundred dollars for a second battery, dual battery isolator, and installation charges (or headaches for the DIY'er). If you are having problems with your charging system then you might need a new or larger alternator. Have it checked out by a qualified technician. For more information on batteries read this chapter.

Car Audio Battery Image courtesy of Lightning Audio

Features and terms with regard to wiring are:

Butt Terminals: This type of terminal resembles a long barrel and is used to connect small gauge wires together. These type are crimp terminals and considered less desirable than soldering when soldering is an option. These terminals are also referred to as crimp connectors.

Deep Cycle: A battery usually reserved for marine use that can be drained and replenished many times. While popular years ago many installers have relegated this battery to system use only with a traditional car battery for main power.

Farad (F): The base unit of measure for capacitor storage. One farad is very large and is equivalent to one million microfarads (uF).

Gauge: This refers to the diameter of the wire. The smaller the number, the larger the wire. Sixteen is common for speaker wire, eight is common for average size amplifiers, while four gauge and below is used for large amplifiers. For reference, four gauge wire is about the same diameter as the average male pinky finger.

Gel Cell: A type of battery that uses a gel type acid. These batteries can be desirable because they may be mounted upside down without the danger a standard type battery would pose.

Heat Shrink Tubing: A type of insulating plastic that resembles a drinking straw. A small portion of this tube is cut off and placed on a wire before soldering. After the connection is soldered and cooled, the tube is moved over the joint and shrunk around the wires by means of a heat gun.

Microfarads (uF): The more common unit used to measure capacitor storage. One million microfarads is equivalent to one Farad.

OFC: An abbreviation for oxygen free copper. This is the most desirable wire to buy. There is really no reason to buy any other kind. As the name implies it is pure copper that is free from oxygen impurities.

Spade Terminals: A type of terminal used on most speakers. The type found on speakers are male spades while the ones used to connect to these terminals are female spades. These terminals are also referred to as quick disconnects though this name can apply to many different types of terminals that come apart quickly.

Voltage Rating: Referring to the amount of voltage a capacitor is rated to handle. The very least a capacitor used for reinforcement should be rated at is 16 volts while 20 volts is much more desirable and available on the slightly more expensive capacitors.

Car Audio Power Capacitors

Web caraudiobook.com

Videos
     Car Stereo Installation
     Car Alarm Installation
     Advanced Enclosures
     Fiberglass Fabrication
     Fiberglass Fabrication II
Back to School Special

Car Audio Background
     What is Sound
     Cabin Gain
     Kick Panels
     Ohm's Law
     Electronic Components
     Electrical System Upgrades

Car Audio Equipment Info
     Car Audio Head Units
     CD Changers and MP3
     Car Audio Speakers
     Choosing a Subwoofer
     Car Audio Amplifiers
     Signal Processors
     Mobile Video
     Satellite and Digital Radio
     Wiring and Power
     Power Capacitors
     Security Systems
     Exotic Components

Car Audio Planning and Buying
     System Planning
     What Fits Your Car
     Budget Systems
     Sample Systems
     OEM Upgrades
     Spotting Good Equipment
     Equipment Reviews
     Where to Buy New
     Tips for Buying New
     Get the Best Retail Deal
     Free Installation
     Common Scams
     Avoiding Bait and Switch
     Mail Fraud Laws
     Where to Buy Used
     Tips for Buying Used
     More Than You Can Afford
     Buying Wholesale
     Selling Used Audio
     Hidden Costs

Car Audio Installation
     Choosing Installers
     Installation Goodies
     Installation Pictures
     Installations You Can Do
     Ten Car Audio Myths
     Amplifier Installation
     Capacitor Installation
     Vehicle Wiring Diagrams
     Noise Troubleshooting
     Car Stereo Help
     Become an Installer

Car Audio Care
     Keeping Your Stereo Safe
     Car Stereo Insurance
     Making Your Stereo Last
     Car Audio Warranties
     Getting Free Repairs
     Avoiding Noise Violations
     Car Audio Safety
     Car Audio Competitions
     The Future of Car Audio